A/C COMPRESSOR 88370-47010
The Changhui compressor for OE 88370-47010 serves the Toyota Prius 2003-2009 hybrid platform. Hybrid climate-control systems place different demands on a compressor: electrically driven operation, strict lubricant insulation requirements and high-voltage service procedures. This unit is supplied as a direct replacement for the original assembly, with matched mounting interfaces and connector geometry, and is intended for workshops equipped for hybrid vehicle work.





Key Features & Product Advantages
Hybrid-Specific Configuration:
Matched to the Prius 2003-2009 electric compressor architecture; not interchangeable with belt-driven units from conventional models.
High-Voltage Connection Ready:
Connector geometry and insulation follow the original design so the factory harness connects without adaptation.
Correct Lubricant Discipline:
Hybrid compressors require an insulating POE-type oil. Never substitute conventional PAG oil, which compromises electrical insulation.
Smooth and Quiet Electric Drive:
Balanced rotating parts and controlled ramp-up keep the cabin quiet when the combustion engine is switched off.
Cooling in EV Mode:
Consistent output at low road speeds and with the engine stopped, where a belt-driven compressor would lose capacity.
Sealed Against Moisture:
New shaft sealing and service-port O-rings protect the circuit; moisture is especially damaging in hybrid systems.
Insulation and Pressure Tested:
Each unit is checked for insulation resistance, leak tightness and pressure performance before packing.
Technical Specifications
|
Parameter |
Specification |
|
Product Type |
Automotive A/C Compressor |
|
OE / Reference Part Numbers |
8837047010 |
|
Vehicle Model |
Fit for PRIUS 2003-2009 |
|
Refrigerant |
R134a |
|
Voltage |
12V |
|
Pulley Grooves |
7PK |
|
Clutch Diameter |
125 mm |
|
Compressor Type |
Variable Displacement |
|
Material |
Aluminum Alloy |
|
Condition |
New |
|
Warranty |
12 Months |
|
Testing |
100% Tested |
Applications
For Toyota Avensis (2001-2009), Camry (2001-2006), FJ Cruiser (2005-2018), Land Cruiser (2002) and Previa (2000-2006) applications specifying OE 88320-35700 or any of the listed cross-references. Confirm the pulley and connector configuration against the original unit before ordering.
Why Partner with Changhui?
Changhui Group has been a Tier-1 manufacturing partner to more than 40 vehicle manufacturers since 1975. Five production bases, in-house tooling and MES-based traceability allow us to support wide-coverage aftermarket references with consistent, repeatable quality.
Recognised Standards: IATF 16949 and ISO 14001 certification, plus EAC conformity documentation for markets where it is required.
Stock-Friendly Supply: Cross-references consolidated into fewer SKUs, brand-new components and dependable schedules for container-level orders.
Installation & Usage Notes
Hybrid A/C service involves high-voltage components. Only trained technicians with the correct insulating tools and service information should carry out this replacement.
1. Make the Vehicle Safe Before Work
Follow the manufacturer's high-voltage isolation procedure, disconnect the service plug and wait the specified discharge time before touching the compressor harness.
2. Use Only Hybrid-Approved Oil
Recover refrigerant with dedicated equipment and cap all opened lines immediately to limit moisture ingress.
Charge only the specified POE-type hybrid compressor oil. PAG oil and universal additives must not be used, as they reduce the insulation resistance of the system.
3. Keep the Circuit Dry and Clean
Measure and match the oil quantity recovered from the original unit; both under-fill and over-fill affect cooling and reliability.
Replace the receiver-drier and all opened seals, then pull a long vacuum to remove every trace of moisture from the circuit.
4. Evacuate Thoroughly and Charge Precisely
Recharge with the exact R134a mass stated for the vehicle and never estimate the charge from pressure readings alone.
Before reconnecting the high-voltage supply, confirm the connector is seated, the harness is undamaged and insulation resistance meets specification.
5. Verify Insulation and Function
Run the climate-control system in both EV and engine-on modes, checking cooling output, current draw and abnormal noise.
Record the insulation test, leak check and vent temperature on the job card to support any later warranty review.
Company Profile


Main Business



Manufacture Capacity - Mold Manufacturing
- Experience in the design and manufacture of stamping, injection and die casting molds.
- With 57 sets of various types of mold processing equipment.
- Processing more than 600 pairs of various types of molds annually.

- 5 Advanced High-Speed SMT Production Lines
- Automated Solder Paste Printing and Reflow Systems
- Efficient Wave Soldering Technology
- AOI Inspection and KIC Temperature Control Monitoring
- Precision 3D Solder Paste Inspection Systems
- Automated Assembly and In-Line Quality Inspection

- Dedicated ECU Motor Production Line
- Full-Process MES Traceability and Production Monitoring
- Components from Globally Recognized Suppliers
- Automated Welding and Assembly Operations
- High-Precision AOI Welding Inspection System

Manufacture Capacity - EPS Manufacturing
- 3 Professional Product Assembly Lines
- Full-Process MES Production Traceability System
- Online Automated Quality Inspection
- Automated Cleaning Equipment
- Fully Automated 3D Warehouse System

Quality Control
1. Comprehensive Performance Testing
Each compressor undergoes rigorous testing for pressure performance, sealing integrity, clutch operation and operating noise to ensure it meets quality requirements before shipment.
2. Precision and Batch Quality Control
Key parameters, including mounting dimensions, pulley run-out, assembly torque and lubricant levels, are inspected and documented through batch-level quality checks.
Certificates

Packing and Transpiration






Hot Tags: a/c compressor 88370-47010, China a/c compressor 88370-47010 manufacturers, suppliers
