A/C COMPRESSOR 88310-0K110

A/C COMPRESSOR 88310-0K110
Details:
Built for the Toyota Hilux 2004-2015, this Changhui compressor (OE 88310-0K110) is specified for vehicles that spend long hours idling, towing or working in high ambient temperatures.
Send Inquiry
Description
Send Inquiry

A/C COMPRESSOR 88310-0K110

 

Built for the Toyota Hilux 2004-2015, this Changhui compressor (OE 88310-0K110) is specified for vehicles that spend long hours idling, towing or working in high ambient temperatures. The housing, clutch and internals are sized for sustained load, while the factory-style mounting pattern keeps the swap simple for workshops. It replaces the original unit directly across the 88310-0K110 / 0K111 / 0K112 / 0K113 / 0K114 reference family.

88310-0K110-AC compressor-connector
88310-0K110-AC compressor-details
88310-0K110-AC compressor-front view
88310-0K110-AC compressor-side view
88310-0K110-AC compressor-top view
 

Key Features & Product Advantages

 

Hilux-Specific Mounting Geometry:
Bolt holes, pulley offset and suction/discharge ports follow the original layout, so the existing belt and hose set can be retained.

Sustained High-Heat Output:
Stable displacement control and efficient heat rejection preserve cooling performance during long idle periods and slow worksite operation.

Protection Against Dust and Corrosion:
A sealed clutch bearing and corrosion-resistant alloy housing stand up to grit, mud and repeated wash-downs on commercial vehicles.

Reinforced Shaft and Bearings:
Upgraded bearing surfaces and a hardened shaft handle the belt loads generated by auxiliary equipment and rough terrain.

Heavy-Duty Sealing:
Double-lip shaft sealing and new port O-rings keep R134a contained over high-mileage fleet duty cycles.

One Unit, Many References:
A single stocked part covers the 88310-0K11x series plus 88310-71062 and the 88320-0K080 / 0K240 / 0K340 / 0K341 / 0K380 references.

Bench-Tested Before Packing:
Each compressor is run on a test stand for pressure, leakage, clutch pull-in and vibration prior to export packing.

 

 

Technical Specifications

 

Parameter

Specification

Product Type

Automotive A/C Compressor

OE / Reference Part Numbers

883100K110 883100K111 883100K112 883100K113 883100K114 8831071062 883200K080 883200K240 883200K340 883200K341 883200K380

Vehicle Model

Fit for HILUX 2004-2015

Refrigerant

R134a

Voltage

12V

Pulley Grooves

7PK

Clutch Diameter

125 mm

Compressor Type

Variable Displacement

Material

Aluminum Alloy

Condition

New

Warranty

12 Months

Testing

100% Tested

 

 

Applications

 

Specified for Toyota Hilux 2004-2015 applications calling for OE 88310-0K110 and its supersessions. Check the number stamped on the old unit or cross-check the VIN before ordering; the full reference list is shown in the specification table.

 

 

Why Partner with Changhui?

 

 

Since 1975 Changhui Group has supplied safety- and comfort-critical components to more than 40 vehicle manufacturers as a Tier-1 partner. The same engineering standards, automated lines and traceable quality records stand behind every compressor delivered to the independent aftermarket.

 

International Approvals: IATF 16949 and ISO 14001 certified manufacturing, with EAC conformity documentation for regulated export markets.

 

Fleet-Ready Availability: Consistent batch quality, shock-protected cartons and dependable replenishment lead times for importers serving commercial-vehicle fleets.

 

 

 

 

Installation & Usage Notes

 

 

A compressor is only as reliable as the system around it. These workshop checks reduce repeat failures on high-mileage pickups.

1. Recover Refrigerant and Isolate the System

Have an equipped workshop recover the R134a, disconnect the battery and remove the drive belt before the old compressor is taken off.

 

2. Remove Contamination from the Failed Unit

If the previous unit seized, flush the condenser and lines and inspect the expansion valve for metal particles before fitting the replacement.

Fit a new receiver-drier at the same time; a saturated drier releases moisture that attacks the new shaft seal.

 

3. Balance the Lubricant Charge

Measure the oil drained from the old compressor and add the same quantity of the specified PAG oil, distributing it between the new unit and the circuit.

Avoid generic all-in-one oils on this platform - incorrect viscosity leads to poor lubrication at high under-bonnet temperatures.

 

4. Inspect Belt Drive and Clutch Air Gap

Inspect the 7-rib belt for glazing, set the correct tension and confirm pulley alignment with the crankshaft and idler.

Verify the clutch air gap to specification; an excessive gap causes slipping and burnt clutch faces under sustained load.

 

5. Run-In and Final Validation

After vacuuming and charging to the labelled R134a mass, run the engine at idle and at 1,500 rpm, cycling the clutch several times.

Log vent temperature and pressures, perform an electronic leak check and re-tension the belt after the first short road test.

 

 

 

Company Profile

 

Company Profile

2

 

 

Main Business

 

 

Main Business

 

Products Automotive electronics series

 

Products Automotive electronics series2

 

 

 

Manufacture Capacity - Mold Manufacturing

 

  • Specialized in stamping, injection, and die casting mold design and manufacturing.
  • 57 sets of mold processing equipment.
  • Annual production capacity of 600+ mold sets.

 

Mold Manufacturing

 

  • 5 High-Speed SMT Production Lines
  • Automated Printing and Reflow Soldering
  • Wave Soldering Process
  • AOI Inspection and KIC Temperature Monitoring
  • 3D Solder Paste Inspection
  • Automated Assembly and Online Inspection

 

Mold Manufacturing

 

  • Dedicated ECU Motor Assembly Line
  • Full-Process MES Production Traceability System
  • Key Components from Leading International Brands
  • Automated Welding, Assembly and Inspection
  • AOI Automatic Optical Inspection for Welding Quality

 

 

Mold Manufacturing

 

 

Manufacture Capacity - EPS Manufacturing

 

  • 3 Professional Product Assembly Lines
  • Full-Process MES Production Traceability System
  • Online Automated Quality Inspection
  • Automated Cleaning Equipment
  • Fully Automated 3D Warehouse System

 

EPS Manufacturing

 

 

Quality Control

 

 

1. Full Functional Test: Pressure rise, leak rate, clutch pull-in and vibration are measured on every unit before it leaves the line.

2. Traceable Batch Control: Assembly torque, oil fill and seal integrity are audited per batch and retained for after-sales reference.

 

 

 

Certificates

 

Certificates

 

Packing and Transpiration

 

Packing and Transpiration

 

Packing and Transpiration3

 

3

 

Product Delivery

 

 

14

15

 

 

Hot Tags: a/c compressor 88310-0k110, China a/c compressor 88310-0k110 manufacturers, suppliers

Send Inquiry