A/C COMPRESSOR 88310-0D010

A/C COMPRESSOR 88310-0D010
Details:
Product Type:Automotive A/C Compressor
OE / Reference Part Numbers:883100D010 883100D020 883100D070 883100D071 883100D140 883100D141 883100D160 888990D081
Vehicle Model: Fit for YARIS 2002-2005
Refrigerant:R134a
Voltage:12V
Pulley Grooves:7PK
Clutch Diameter:125 mm
Compressor Type: Variable Displacement
Material: Aluminum Alloy
Send Inquiry
Description
Send Inquiry

A/C COMPRESSOR 88310-0D010

 

Designed for the Toyota Yaris 2002-2005, the Changhui compressor supplied under OE 88310-0D010 brings the original climate-control system back to full cooling performance in a compact, space-efficient package. Mounting points, pulley alignment, and port angles follow the factory layout, so the unit drops into the tight Yaris engine bay without adaptors or modified brackets. For distributors and service networks, it is a straightforward, low-comeback replacement for a noisy or leaking factory unit.

88310-0D010-AC compressor-connector
88310-0D010-AC compressor-details
88310-0D010-AC compressor-front view
88310-0D010-AC compressor-side view
88310-0D010-AC compressor-top view
 

Key Features

 

Direct Fit for OE 88310-0D010:
Machined to the original mounting geometry, belt line, and refrigerant port positions of the Yaris platform, so fitting requires no cutting, drilling, or custom hoses.

Quiet, Low-Vibration Running:
A dynamically balanced rotating assembly and controlled internal clearances keep cabin noise low - a detail that matters on small hatchbacks where compressor NVH is easy to notice.

Fast Cool-Down in City Traffic:
Stable displacement control holds consistent suction pressure at idle and in stop-and-go driving, helping the cabin recover quickly after a hot soak.

Leak-Resistant Sealing Package:
Multi-lip shaft seals and fresh service-port O-rings hold system pressure and prevent the slow refrigerant loss that causes weak cooling on ageing vehicles.

Lightweight Alloy Housing:
A corrosion-resistant aluminium body sheds heat efficiently while hardened internals cope with frequent clutch cycling in urban use.

Less Load on Small Engines:
Optimised compression efficiency and low-friction internals limit the torque taken from the Yaris powertrain, protecting drivability and fuel economy.

Checked Before Dispatch:
Every unit is verified for pressure build-up, leak tightness, clutch engagement, and running noise, with results logged against its production batch.

 

 

Technical Specifications

Parameter

Specification

Product Type

Automotive A/C Compressor

OE / Reference Part Numbers

883100D010 883100D020 883100D070 883100D071 883100D140 883100D141 883100D160 888990D081

Vehicle Model

Fit for YARIS 2002-2005

Refrigerant

R134a

Voltage

12V

Pulley Grooves

7PK

Clutch Diameter

125 mm

Compressor Type

Variable Displacement

Material

Aluminum Alloy

Condition

New

Warranty

12 Months

Testing

100% Tested

 

 

Applications

 

Suitable for Toyota Yaris 2002-2005 vehicles that specify OE 88310-0D010 and its related references 88310-0D020, 0D070, 0D071, 0D140, 0D141, 0D160 and 88899-0D081. Match the number on the original unit or confirm by VIN before placing a bulk order.

 

 

Why Partner with Changhui?

 

Changhui Group has engineered and manufactured automotive components since 1975. As a long-standing Tier-1 partner to more than 40 vehicle manufacturers worldwide, we apply the same process control, tooling discipline and end-of-line verification to every aftermarket compressor we ship.

 

Certified Quality Systems: Production is managed under IATF 16949 and ISO 14001, with EAC documentation available for markets that require it.

 

Reliable Distribution Supply: Brand-new units only, protective export packaging, stable batch availability, and published lead times for stocking distributors.

 

 

 

Installation & Usage Notes

 

Correct installation matters as much as component quality. The following workshop checks protect the new compressor and keep the 12-month warranty valid.

1. Use a Qualified A/C Technician

Air-conditioning work needs recovery equipment, a vacuum pump, and a calibrated charging scale. Entrust the replacement to a certified workshop rather than a DIY repair.

 

2. Flush the Circuit and Replace the Drier

When an original compressor fails, debris can travel through the condenser and lines. Flush the circuit and fit a new receiver-drier or drier cartridge before this unit is installed.

Skipping that step is the most common cause of premature wear and repeat warranty claims on small Toyota systems.

 

3. Set the Correct Oil Charge

Use the R134a-compatible PAG oil grade and quantity specified for this vehicle; drain and measure the oil recovered from the old compressor before topping up.

Never mix oil grades or overfill the system - excess oil reduces cooling capacity and can damage the reed valves.

 

4. Evacuate and Charge by Weight

Pull a deep vacuum for at least 30 minutes and confirm it holds, removing air and moisture while proving the circuit is sealed.

Recharge with the exact R134a mass stated on the vehicle label. Charging by pressure alone is not accurate on a small system.

 

5. Verify Belt, Clutch and Output

Check multi-rib belt alignment and tension, confirm the clutch engages cleanly with the correct air gap, and inspect the electrical connector.

Record vent temperature, high- and low-side pressures, and a final leak check before handing the vehicle back to the customer.

 

 

Company Profile

 

Company Profile

2

 

 

Main Business

 

 

Main Business

 

Products Automotive electronics series

 

Products Automotive electronics series2

 

 

 

Manufacture Capacity - Mold Manufacturing

 

Experience in the design and manufacture of stamping, injection and die casting molds.

With 57 sets of various types of mold processing equipment.

Processing more than 600 pairs of various types of molds annually.

 

Mold Manufacturing

 

5 high-speed SMT mounting production lines

Fully automatic printing machine, reflow soldering

Wave soldering

AOI automatic optical inspection, KIC thermometer,

3D solder paste inspector product assembly line

Online automated inspection

 

Mold Manufacturing

ECU motor assembly production line

The whole process of MES production

line traceability system

The key components of the whole line adopt international first-line brands

Fully automatic welding, assembly and

automatic inspection

Welding process AOI automatic optical inspection

 

Mold Manufacturing

 

 

Manufacture Capacity - EPS Manufacturing

 

3 professional assembly lines

Whole process MES production line traceability system

On-line automated inspection

Cleaning machine

Fully automatic three-dimensional warehouse

 

EPS Manufacturing

 

 

Quality Control

 

1. 100% End-of-Line Verification: Each compressor is tested for pressure output, leak tightness, clutch engagement and running noise before release.

2. Batch-Level Audit: Machining accuracy, assembly torque, lubricant fill and seal integrity are sampled and documented for every production batch.

 

 

Certificates

 

Certificates

 

Packing and Transpiration

 

Packing and Transpiration

 

Packing and Transpiration3

 

3

 

Product Delivery

 

 

14

15

 

 

Hot Tags: a/c compressor 88310-0d010, China a/c compressor 88310-0d010 manufacturers, suppliers

Send Inquiry