A/C COMPRESSOR 88320-35700
The Changhui compressor supplied under OE 88320-35700 is engineered for the broad Toyota coverage listed in the specification table: Avensis, Camry, FJ Cruiser, Land Cruiser and Previa. One reference serves several model lines, making it a practical stocking choice for distributors supporting mixed fleets. Factory-matched mounting points, port angles and pulley alignment keep installation predictable across all listed applications.





Key Features & Product Advantages
Multi-Platform Interchangeability:
A single unit serves the Yaris-to-Land Cruiser range listed below, cutting the number of part numbers a distributor needs to hold.
Stable Output Across Engine Variants:
Variable displacement control adapts cooling demand to different engine sizes without overloading the drive belt.
Extensive Cross-Reference Coverage:
The reference list includes 88310-28450 / 28530 / 28550 / 35830 / 44160 / 44200 and the 88320-28xxx, 35xxx, 44xxx, 48xxx and 6A010 families.
Durable Rotating Assembly:
Precision-ground internals and a robust bearing pack tolerate high mileage and frequent stop-start operation in taxi and fleet service.
Reliable Pressure Integrity:
New shaft seals and O-rings maintain system pressure and reduce the risk of gradual refrigerant loss between services.
Heat-Resistant Alloy Finish:
The aluminium housing dissipates heat effectively and resists corrosion in both hot climates and winter road-salt conditions.
Documented Final Inspection:
Pressure, leakage, clutch and noise results are recorded for every unit prior to protective export packing.
Technical Specifications
|
Parameter |
Specification |
|
Product Type |
Automotive A/C Compressor |
|
OE / Reference Part Numbers |
88310-28450 88310-28530 88310-28550 88310-35830 88310-44160 88310-44200 8831028450 8831028550 8831048060 88320-28350 88320-28410 88320-35700 88320-35700-84 88320-44130 88320-48080 88320-48080-84 88320-6A010 88320-6A011 88320-YC010 8832006084 8832028350 883202835084 8832048080 883204808084 8832048084 88410-35430 |
|
Vehicle Model |
Fit for Avensis 2001-2009 Fit for Camry 2001-2006 Fit for FJ Cruiser 2005-2018 Fit for Land cruiser 2002 Fit for Previa 2000-2006 |
|
Refrigerant |
R134a |
|
Voltage |
12V |
|
Pulley Grooves |
7PK |
|
Clutch Diameter |
125 mm |
|
Compressor Type |
Variable Displacement |
|
Material |
Aluminum Alloy |
|
Condition |
New |
|
Warranty |
12 Months |
|
Testing |
100% Tested |
Applications
For Toyota Avensis (2001-2009), Camry (2001-2006), FJ Cruiser (2005-2018), Land Cruiser (2002) and Previa (2000-2006) applications specifying OE 88320-35700 or any of the listed cross-references. Confirm the pulley and connector configuration against the original unit before ordering.
Why Partner with Changhui?
Changhui Group has been a Tier-1 manufacturing partner to more than 40 vehicle manufacturers since 1975. Five production bases, in-house tooling and MES-based traceability allow us to support wide-coverage aftermarket references with consistent, repeatable quality.
Recognised Standards: IATF 16949 and ISO 14001 certification, plus EAC conformity documentation for markets where it is required.
Stock-Friendly Supply: Cross-references consolidated into fewer SKUs, brand-new components and dependable schedules for container-level orders.
Installation & Usage Notes
Because this reference spans several platforms, correct identification and clean system preparation are the two keys to a trouble-free replacement.
1. Confirm the Reference Before Fitting
Compare the number on the old compressor with the cross-reference table and verify pulley grooves and connector shape; several Toyota variants share the casting but not the clutch.
2. Clean the Whole Refrigerant Circuit
Flush lines and condenser whenever the previous compressor showed internal wear, and inspect the expansion valve for restricted flow.
Replace every opened O-ring with a new R134a-compatible seal and fit a fresh receiver-drier to protect the shaft seal from moisture.
3. Renew Seals and the Drier
Use the specified PAG oil grade and quantity, then pull a full vacuum and confirm the system holds it before charging.
Charge R134a strictly by the mass printed on the vehicle label, not by gauge pressure, and record the final amount on the job card.
4. Evacuate, Charge and Check Oil
Check belt tension and alignment, clutch air gap and the 12 V connector for corrosion or loose terminals.
Run the system at idle and at raised engine speed, confirming stable high- and low-side pressures and a clean clutch engagement.
5. Validate Electrical and Drive Components
Finish with an electronic leak check at all joints and a vent-temperature measurement before the vehicle is returned.
Keep the installation record with the invoice; it is required to validate any warranty claim.
Company Profile


Main Business



Manufacture Capacity - Mold Manufacturing
- Experience in the design and manufacture of stamping, injection and die casting molds.
- With 57 sets of various types of mold processing equipment.
- Processing more than 600 pairs of various types of molds annually.

- 5 High-Speed SMT Production Lines
- Automated Printing and Reflow Soldering
- Wave Soldering Process
- AOI Quality Inspection and KIC Thermal Monitoring
- Advanced 3D Solder Paste Inspection Technology
- Automated Product Assembly with Real-Time Online Quality Checks

- Specialized ECU Motor Manufacturing Line
- MES-Based End-to-End Production Tracking
- Premium Components Sourced from Global Leading Suppliers
- Integrated Automatic Welding and Assembly Processes
- Advanced AOI Systems for Welding Quality Inspection

Manufacture Capacity - EPS Manufacturing
- 3 Professional Product Assembly Lines
- Full-Process MES Production Traceability System
- Online Automated Quality Inspection
- Automated Cleaning Equipment
- Fully Automated 3D Warehouse System

Quality Control
1. Performance Verification: Every compressor is measured for pressure output, leak tightness, clutch response and noise before approval.
2. Dimensional and Batch Audit: Mounting faces, pulley run-out, assembly torque and oil fill are checked and recorded per batch.
Certificates

Packing and Transpiration






Hot Tags: a/c compressor 88320-35700, China a/c compressor 88320-35700 manufacturers, suppliers
